Model：
SWTB8000-1
Parameter：
| Power amplifier | 1 | Type | SSRFPA |
| 2 | Work mode | Pulse | |
| 3 | Work Frequency | 4GHz~6GHz;6GHz ~8GHz; 8GHz~10GHz; 10GHz~12GHz; 12GHz~15GHz; 15GHz~18GHz; | |
| 4 | Saturate drive signal power | -10dBm~10dBm(typical-10dBm) | |
| 5 | Input power range | -50dBm~10dBm | |
| 6 | Output power | >1000W | |
| 7 | Pulse width | 0.2ps~lOOgs | |
| 8 | Pulse rise/fall time | <30ns (10%~90%) WlOOns (0%~90%, 0% power turned off,without any signal output) | |
| 9 | Top drop | <0.5dB (saturated output) | |
| 10 | Dmax | 20% | |
| 11 | Power Gain flatness | ≤±1dB | |
| 12 | Stability | <0.5dB (10minutes~4H) | |
| 13 | Coupling degree | 50dB±ldB | |
| 14 | Detection type | Pulse detection（logarithmic detector） | |
| 15 | Detection pulse characteristics | Rise,Fall:< 30 ns(Design Assurance;pulse width:0.1~100us) | |
| 16 | Power feedback value | >50dB | |
| 17 | Switching time | <300ms (Design assurance) | |
| 18 | Degree of switch isolation | >60dB | |
| 19 | Degree of reverse isolation | >20dB (Design assurance) | |
| 20 | Spurious signal | <-60dBc | |
| 21 | Controlling | 422 differential level, supporting a maximum transmission rate greater than 10Mbps | |
| 22 | Input port | SMA-K | |
| 23 | Output port | N-K head/waveguide | |
| 24 | Input and output impedance | 50Ω (except waveguide port) |
| No | Frequency | Dimensions (mm) | Weight (kg) |
| 1 | 4GHz~6GHz | <552*470*316 | <35 |
| 2 | 6GHz~8GHz | <70*442*308 | <35 |
| 3 | 8GHz~10GHz | <403*410*255 | <28 |
| 4 | 10GHz~12GHz | <403*410*255 | <28 |
| 5 | 12GHz~15GHz | <520*407*318 | <35 |
| 6 | 15GHz~18GHz | <502*450*218 | <30 |
Interface Defination:
1)Low power RF signal input: SMA-K;
2)Monitoring signal:SMA-K;
3)Power connector:Y17-1003ZJ
4)Control connector:y50x - 1019 z10j02;
5)Transmit:N-K(4~12GHz)、BJ140 (12~18GHz)。
Equipment capacity:
Power: AC220V 176 v - 264 v / 50 hz.
With local/remote switch, it can switch the working state of the local control and remote control of the power amplifier.
A power switch needs to be installed on each amplifier panel. The local/remote switch is in the "local" state to realize the channel power switch control. In practice, the switch is in the "on" state, and the "on" and "off" control of the channel power supply can be realized by remote control. Therefore, the overall electrical design, especially the power module, needs to be adapted to instantaneous power-on applications.
Integrated structure, dust and rain proof, can work in outdoor environment for a long time.
Work enviroment:
Working temp.:-20°C-60°C
Storage temp.:-40°C ~ + 70°C
Ralative humidity:<95%(20℃)，<70%(50℃)